There are methods which you have to remember when you are installing new items. You have to follow it so that you would be able to install the Profile Design Cobra bars correctly. It is also required under the policy of the warranty that they would be giving to you. If you do not know how to do it, you should visit the dealer in your area.
You would be provided with a manual that indicates the procedures you must follow. If you prefer to get it done yourself, the tools that will be utilized on that must be prepared. An Allen or a torque wrench should be prepared. You will be needing a sandpaper since that will be utilized in making the parts smooth. When you got all of those tools, you may begin on this.
You should avoid greasing the clamping area. If you would be greasing it, it would only cause the bar to slip from it. You have to make sure that such situation would not happen especially when you are already using your bike. It would cause you to lose control while you are riding the bike. It would be very dangerous on your part if that would happen.
You have to make sure that the diameter of the bar clamp would match to the diameter of its stem. This should be checked so that you could avoid any problems with it. It would not fit if their diameter would not be the same. Before you would buy, you have to check the diameter so you would not waste your money on buying one.
If one is going to install a stem which is new, the manufacturer also provides an instruction for that. The manufacturer would set the procedures on how a person will have the capability to properly do such task. That is stated on a manual which has been given to him so he is not going to experience any difficulties while he is going to do this.
One has to inspect its front step clamp as there could be edges that are sharp. Use a sandpaper to get rid of that. The fibers of that aluminum or fiber of the carbon would be damaged if that is not made properly. When you have it on the right position, it has to be clamped to its stem. You must ensure that this will be tight.
You have to slide its level on that bar. If it will be uncomfortable for you, you can adjust that based on what you wanted. You should be placing that slowly. You should not forget that when it gets broken, the warranty of that material will not be valid.
You could wrap it if you want to. If you would try it, you have to make sure that you are wearing your helmet. Check if it would be working properly before you would be using it on far away places.
It is important that you would be following those methods. It would be very risky as you would lose control of the bike. It can even cause serious injuries to the person.
You would be provided with a manual that indicates the procedures you must follow. If you prefer to get it done yourself, the tools that will be utilized on that must be prepared. An Allen or a torque wrench should be prepared. You will be needing a sandpaper since that will be utilized in making the parts smooth. When you got all of those tools, you may begin on this.
You should avoid greasing the clamping area. If you would be greasing it, it would only cause the bar to slip from it. You have to make sure that such situation would not happen especially when you are already using your bike. It would cause you to lose control while you are riding the bike. It would be very dangerous on your part if that would happen.
You have to make sure that the diameter of the bar clamp would match to the diameter of its stem. This should be checked so that you could avoid any problems with it. It would not fit if their diameter would not be the same. Before you would buy, you have to check the diameter so you would not waste your money on buying one.
If one is going to install a stem which is new, the manufacturer also provides an instruction for that. The manufacturer would set the procedures on how a person will have the capability to properly do such task. That is stated on a manual which has been given to him so he is not going to experience any difficulties while he is going to do this.
One has to inspect its front step clamp as there could be edges that are sharp. Use a sandpaper to get rid of that. The fibers of that aluminum or fiber of the carbon would be damaged if that is not made properly. When you have it on the right position, it has to be clamped to its stem. You must ensure that this will be tight.
You have to slide its level on that bar. If it will be uncomfortable for you, you can adjust that based on what you wanted. You should be placing that slowly. You should not forget that when it gets broken, the warranty of that material will not be valid.
You could wrap it if you want to. If you would try it, you have to make sure that you are wearing your helmet. Check if it would be working properly before you would be using it on far away places.
It is important that you would be following those methods. It would be very risky as you would lose control of the bike. It can even cause serious injuries to the person.
About the Author:
Read more about Procedures On Installing Profile Design Cobra Bars You Must Follow.
No comments:
Post a Comment